ISO 14998 PDF

Leave a comment

Industries du pétrole et du gaz natruel — Équipement de fond de trou — Accessoires de complétion. STANDARD. ISO. First edition. Products covered under ISO , ISO , ISO , ISO , ISO , ISO , ISO ‑2, ISO , and ISO ‑1 are not included. STANDARD. ISO. First edition. Reference number. ISO (E). This is a free 6 page sample. Access the full version online.

Author: Taunris Kigashakar
Country: Dominican Republic
Language: English (Spanish)
Genre: Education
Published (Last): 22 October 2016
Pages: 46
PDF File Size: 8.67 Mb
ePub File Size: 12.64 Mb
ISBN: 514-5-65546-957-9
Downloads: 16639
Price: Free* [*Free Regsitration Required]
Uploader: JoJokree

The main task of technical committees is to prepare International Standards. Start Webshop Io catalog Product presentation. Inside diameters, cross sections, tolerances and size identification code ISOFluid power systems — O-rings — Part 3: ID drift shall only apply to completion accessory IDs not designed as sealing surfaces sealbores.

ISO CD Changes to a component or series of components may be identified as a substantive change and require design validation. When a furnace is repaired or rebuilt, a new survey shall be required before heat treating.

ISO 14998:2013

The material sample shall experience the same heat treatment ios as the component it qualifies. For undated references, the latest edition of the referenced document including any amendments applies. International Standard Document subtype: The work of preparing International Standards is normally carried out through ISO technical committees.

If the envelope covers two or more products that are used together down-hole, then this shall be stated on the envelope. Drift bar dimensions shall meet the requirements specified in ISO Rated performance envelopes can have ratings of zero for pressure if applicable.

Products shall be supplied to at least the design validation grade specified. ISO CD 7.


Rives Basane

Also not included are other products such as: Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work. Graduated cylinders for accumulated gas shall be at atmospheric pressure. You need to log in before adding standards to the monitoring service.

Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s member body in the country of the requester. The test shall adequately simulate the loading conditions that would be present if the entire assembly were tested.

This applies to products validated to grade V5 through grade V0, in accordance with 6. All documentation and data associated with design verification, design validation and design change justification shall be maintained for ten years after date of last manufacture. The bubble rate shall not increase during the hold period. NOTE Rated performance envelopes can have ratings of zero for pressure if applicable. If the completion accessory is also rated for any of the other functionalities listed in Table 1, then the requirements of these annexes shall also be met for the same validation grade as the Annex A testing.

The following information shall be included as a minimum: Completion accessories shall not be rated for the following functionalities without meeting the requirements of Annex B for the selected design validation grade: Evaluation results shall be approved by qualified person other than the person performing them and records of the results shall become a portion of the design documentation.

Petroleum and natural gas industries- Downhole equipment Pages 1 – 49 – Text Version | AnyFlip

Quality control requirements are detailed in 7. Sampling procedures shall 114998 be established based on the documented variation history.


This International Standard provides seven standard design validation grades V6 to V0as defined in 6. This International Standard provides requirements for the functional specification, technical specifications including; design, design verification and validation, materials, documentation and data control, repair, shipment, and storage.

Functional test data shall be recorded, dated and signed by the qualified person performing the tests. Design changes identified as non-substantive shall include documented justification. It is subject to change without notice and may not be referred to as an International Standard.

The hardness results shall verify through documented correlation that the mechanical properties of the material tested meet the properties specified.

ISO – Standards Australia

ISOSampling procedures for iao by attributes — Part 1: The single specified design validation grade applies to all validation testing per Annex A thru Annex D, as applicable. NOK 1 ,00 excl. These include requirements for documentation and data control, product identification, quality control, functional testing, repair, redress, shipping, and storage.

Webprint Printed and bound.

The words you are searching are inside this book. The moment new editions of the standards you monitor are released, ixo are made, or appendixes are published, you will be alerted by email. Table 1 — Design validation grades Validation Annex A: Products shall be supplied to at least the quality control grade specified. Petroleum and natural gas industries — Downhole equipment — Completion accessories.